Light Curtain Type 4 PLe SIL3 SF4C

Safety light curtain individual specifications

SF4C-F□

SF4C-H□

Safety light curtain common specifications

<When selecting NPN output>
・Max. sink current: 200 mA
・Applied voltage: same as supply voltage
(between the control output and 0 V)
・Residual voltage: 2.5 V or less
(sink current 200 mA, when using 10 m 32.808 ft length cable)
・Leakage current: 200 μA or less (including power supply OFF condition)
・Max. load capacity: 1 μF (No load to Max. sink current)
・Load wiring resistance: 3 Ω or less
Operation
modeON when all beam channels are received, OFF when one or more beam channels are interrupted
(OFF also in case of any malfunction in the safety light curtain or the synchronization signal)(Note 6,7)Protection
circuitIncorporatedResponse timeOFF response: 9 ms or less, ON response: 90 ms or lessOFF response: 9 ms or less, ON response: 90 ms or lessOFF response: 7 ms or less, ON response: 90 ms or lessOFF response: 9 ms or less, ON response: 90 ms or lessAuxiliary output
(Non-safety output)PNP open-collector transistor / NPN open-collector transistor (switching method)
<When selecting PNP output>
・Max. source current: 100 mA
・Applied voltage: same as supply voltage
(between the auxiliary source and +V)
・Residual voltage: 2.5 V or less
(source current 100 mA, when using 10 m 32.808 ft length cable)

<When selecting NPN output>
・Max. sink current: 100 mA
・Applied voltage: same as supply voltage
(between the auxiliary sink and 0 V)
・Residual voltage: 2.5 V or less
(sink current 100 mA, when using 10 m 32.808 ft length cable)
Operation
modeOFF when control outputs are ON, ON when control outputs are OFF [Factory setting, operating mode can be changed using the handy-controller SFC-HC(optional).]Protection
circuitIncorporatedELCA functionIncorporated (reducing mutual interference automatically)Test / reset input functionIncorporatedInterlock functionIncorporated [Manual reset / Automatic reset (Note 8)]External device
monitoring functionIncorporatedSafety input functionIncorporated (safety contact)Muting functionIncorporatedOverride functionIncorporatedOptional functions
(Note 9)Fixed blanking, floating blanking, auxiliary output change, safety input (safety sensor), large multi-purpose indicator setting change, interlock setting change, external relay monitoring setting change, muting setting change, override setting change, protectingPollution degree3Operating altitude2,000 m 6,561 68 ft or less (Note 10)Degree of protectionIP67 / IP65 (IEC)Ambient temperature-10 to +55 ℃ +14 to +131 ℉
(No dew condensation or icing allowed),
Storage: -25 to +60 ℃ -13 to +140 ℉Ambient humidity30 to 85 % RH, Storage: 30 to 85 % RHAmbient illuminanceIncandescent light: 5,000 lx or less at the light-receiving faceDielectric strength
voltage1,000 V AC for one min. between all supply terminals connected together and enclosureInsulation resistance20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosureVibration resistance10 to 55 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours eachShock resistance300 m/s² acceleration (30 G approx.) in X, Y and Z directions three times eachEmitting elementInfrared LED (Peak emission wavelength: 855 nm 0.034 mil)MaterialEnclosure: Polycarbonate alloy, Sensing surface: Polycarbonate alloyCable0.15 mm² (power line: 0.2 mm²) 12-core heat-resistant PVC cable with connector, 0.5 m 1.640 ft long0.15 mm² (power line: 0.2 mm²) 12-core heat-resistant PVC cable, 5 m 16.404 ft longCable extensionExtension up to 40.5 m 132.874 ft is possible for both emitter and receiver optional mating cablesExtension up to 40.5 m 132.874 ft is possible for both emitter
and receiver, with 0.2 mm2 or more cable (Note 11) (Note 12)AccessoriesMS-SFC-1 (Standard mounting bracket): 1 set,SF4C-TR14 (Test rod): 1 No.MS-SFC-1 (Standard mounting bracket): 1 set,SF4C-TR25 (Test rod): 1 No.MS-SFC-1 (Standard mounting bracket): 1 set,SF4C-TR14 (Test rod): 1 No.MS-SFC-1 (Standard mounting bracket): 1 set,SF4C-TR25 (Test rod): 1 No.

Notes:
1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 ℃ +68 ℉.
2) Regarding EU Machinery Directive, a Notified Body, TUV SUD, has certified with the type examination certificate.
3) With regards to the standards in the US, under the US regulation 29 CFR 1910.7, TÜV SÜD, a Nationally Recognized Testing Laboratory (NRTL) certified by OSHA, has certified with the safety certificate based on UL/ANSI standards. With regards to the standards in Canada, under the safety regulations based on CEC (Canadian Electric Code), TÜV SÜD America, a Certification Body accredited by SCC, has certified with the safety certificate based on CSA standards.
4) The operating range is the possible setting distance between the emitter and the receiver.The safety light curtain can detect an object less than 0.1 m 0.328 ft away.
5) When the floating blanking function is used, the size of the min. sensing object is changed.
6) The outputs are not “OFF” when muting function is active even if the beam channel is interruped.
7) In case the blanking function is valid, the operation mode is changed.
8) The manual reset and automatic reset are possible to be switched depending on the wiring status.
9) In case of using optional function, the handy-controller SFC-HC(optional) is required.
10) Do not use or store in an environment pressurized to atmospheric pressure or higher at an altitude of 0 m.
11) When the muting lamp is used, the cable can be extended within 30.5 m 100.066 ft (for emitter / receiver).
12) When the synchronization + wire (orange) and synchronization – wire (orange / black) is extended with a cable other than exclusive cable, use a 0.2 mm² or more shielded twisted pair cable.

Handy-controller

Tab content