Hỗ trợ trực tuyến

Hỗ trợ kỹ thuât

  • Selling products
  • Panasonic Product

  • Hakko Products

  • SMC Product

  • Schleuniger Products

  • RKC Product

  • adpack products

  • kyowa product

  • t-h-m product

  • Rgl product

  • OTSUKA products

  • OSAWA productS


  • Other Product

Info: Your browser does not accept cookies. To put products into your cart and purchase them you need to enable cookies.


Price: Liên hệ


BCD data output No
High/low limit Comparative function Yes
Peak hold function Yes
Analog (D-A) Output Yes
TEDS Compatible No
RS-232C No


Control Input Number of commands : 3 Kinds : HOLD, HOLD RESET, BALANCE. Input system : No-voltage contact signal or open collector signal (should enable application of 12V DC and current flow of 5 mA.)
Power Supply AC 100 to 240V±10%, 50/60 Hz, 20 VA or less
Applicable Bridge Resistance 87.5Ω to 10kΩ(Up to 4 transducers with 350Ωbridge resistance can be connected in parallel)
Measuring Range ±3.2 mV/V (including tare) (±6400μm/m)
Adding Function Setting range ±19999
Sampling rate 2000 times/sec.
Bridge Excitation 10V DC/2V DC, switchable by panel switch
Analog (D-A) Output Setting items : Indication for 0 V output (±19999), Indication for 10 V output (±19999)
Nonlinearity : Within ±0.1% FS
Number of Measuring Channels 1.0
Weight Approx. 1.1 kg
Calibration function Possible by inputting a numeric value or by applying an actual load
Applicable transducer Strain gage transducers
Indicator ±19999 (Decimal point can be put anywhere.) Character height 14 mm, red LED Mode : Normal/hold Update : 15.6 times/sec. in normal mode
Analog (D-A) Output Current Output : 4 to 20 mA (load resistance 500Ωor less) Corresponds to voltage output of 0 to 10 V.
Check Function Self-check
Analog (D-A) Output Voltage Output : ±10 V (load resistance 2kΩ or more), Desired scaling possible
High/low limit Comparative function Number of setting points : 2 (high limit, low limit), Setting range : ±19999, Max. Hysteresis width : Can be set in a range of 0 to 19999, Output : Open collector, Load capacity : 30 VDC, 20 mA (resistive load), Comparison mode : Normal/hold, Comparison rate : 500 times/sec.
EMC Standard Conforms to IEC61326-1 (class A)
Operating Temperature/Humidity Range -10 to 50°C, 20 to 85% RH (noncondensing)
Safety Standard Conforms to IEC61010-1 (installation category II, pollution degree 2)
Dimensions 96(W)×96(H)×139(D)mm (excluding protrusions)
Analog (D-A) Output Stability : Sensitivity stability : Within ±0.01%/°C
Zero stability : ±150 μV RTI /°C
Frequency Response Range DC to 100 Hz (within -3 dB at 100 Hz) DC to 10 Hz (within -3 dB at 10 Hz)
Nonlinearity Within ±(0.03% FS + 1 digit)
Panel Cut Dimensions 92×92mm
Original Value Measurement Function ±3.200mV/V
Digital Zero Adjustment Range Same as measuring range (digital adjustment only)
Measurement Mode Time-based peak hold : Peak in a designated period is held.
Input/Output Terminal Board M3 screw terminal (Applicable crimp-style terminal V1.25-3A, 1.25-3B or the equivalent)
Analog (D-A) Output Resolution : 13 bits
Conversion rate : 500 times/sec.
Insulation withstand voltage between the DA-output and main circuit : 250 VAC for one minute (Circuit between voltage output and current output is not isolated.)
Measurement Mode Point-based hold : Value measured at a selected point is held.
Section-based peak hold : Peak in a designated section is held.
Peak hold : Holds a maximum value during measurement.
Normal : Measured value is normally indicated.
Zero compensation function Automatic zero compensation : Uses digital zero within set range. Approximated zero compensation : Indication is made zero when the reading is in a preset range of 0 to 9.
Smoothing Function Minimum scale : 1, 2, 5, 10, 20, 50, 100, 200, 500, 1000 counts. Number of moving averaging times : 8, 16, 32, 64, 128, 256, 512, 1024, 2048. Analog filter : 10, 100 Hz
Stability Zero Stability : within ±0.25 μVRTI / °C, Sensitivity Stability : within ±0.01%/°C
Applicable Standard
EMC Directive EN61326-1(Class A)
Low Voltage Directive EN61010-1, EN61010-2-030
(Installation Category Ⅱ, Pollution Degree 2, Measurement Category O)
RoHS Directive EN50581
Standard Accessories Unit seal, Instruction Manual

Optional Accessories

Optional Accessories ●AC power cables
2 m long with round crimp-style terminal (M3) to
WGA-670B and flat power plug to wall outlet
P-23 for 100 VAC
P-28 for 200 VAC
●Input cables U-33 to U-36
For connection between WGA-670B and
transducer with NDIS connector; NDIS connector
to transducer and round crimp-style terminal (M3)
to WGA-670B
U-33 50 cm long, U-34 1 m long, U-35 2 m long,
U-36 5 m long

Last Updated: Friday, 18 June 2021 21:22